Multifunction Electronic Modules

-


Description and Operation
Overview
Click to resize E84394
 
Item
Part Number
Description
1
-
HS CAN bus
2
-
MS CAN bus
3
-
Gateway (GEM)
4
-
GEM.
5
-
Front/rear window wiper motors
6
-
Headlamp
7
-
Fuel pump module (FPDM)
8
-
Heated windscreen
9
-
Heated rear window, heated exterior mirrors
10
-
Window washer pump
11
-
Headlamp washer pump
12
-
Electric booster heater
13
-
Instrument cluster
14
-
Remote control/tire pressure monitoring receiver module (vehicles without keyless vehicle module only)
15
-
Tire pressure monitoring antenna
16
-
Yaw rate sensor
17
-
Clutch travel sensor
18
-
Ignition lock
19
-
Stoplamp switch
20
-
Fuel level sensor
21
-
Accelerator pedal position (APP2) sensor
22
-
Backup lamp switch
23
-
Multifunction switch
24
-
PATS transceiver (vehicles without keyless vehicle module only)
25
-
Speed control switch
26
-
Windscreen heater switch
27
-
Rear window heater switch
28
-
Evaporator temperature sensor
29
-
Hazard flasher switch
30
-
Brake fluid level switch
31
-
Light switch module
32
-
Light/rain sensor

Commentaires

Enregistrer un commentaire

Posts les plus consultés de ce blog

Automatic Transmission - 6-Speed PowerShift Transmission - MPS6/6DCT450 - Diagnostic Strategy

-
Image
Diagnosis and Testing Refer to Wiring Diagrams Section 307-01, for schematic and connector information. General Equipment  diagnostic equipment Inspection and Verification Verify the customer concern. Visually inspect for obvious signs of mechanical or electrical damage. Visual Inspection Mechanical Electrical Fluid level too high/low Poor condition of fluid Fluid leak Damaged shift mechanism/linkages Damaged automatic transmission/ transaxle casing Fuse(s) Relay(s) Wiring harness Electrical connector(s) Selector lever module Transmission control module (TCM) If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step If the cause is not visually evident, verify the symptom and refer to the Ford diagnostic equipment to diagnose the system. Diagnostic Trouble Code (DTC) Chart NOTE: The following table should be used for guida...
Lire la suite

Electronic Engine Controls - 1.6L EcoBoost (118kW/160PS)

-
Image
Description and Operation Front view of engine Item Description 1 Variable camshaft timing oil control solenoid, exhaust camshaft 2 Ignition coil-on-plugs 3 CMP  (camshaft position)  Sensor - intake camshaft 4 Bypass solenoid valve 5 KS  (knock sensor)  sensor – cylinders 3 and 4 6 Electric throttle plate position sensors 7 Oil pressure switch 8 Shut-off solenoid valve 9 Electrically heated thermostat 10 KS  sensor – cylinders 1 and 2 11 The  MAP  (manifold absolute pressure)  sensor 12 Variable camshaft timing oil control solenoid, intake camshaft 13 Fuel pressure sensor – high-pressure circuit Rear view of engine Item Description 1 CMP  Sensor - exhaust camshaft 2 Fuel Metering Valve Comments: Part of the high-pressure fuel pump 3 Two-point  HO2S  (heated oxygen sensor) ...
Lire la suite

Diagnostic et essais Allumage automatique des phares

-
Image
Eclairage extérieur - Allumage automatique des phares Diagnostic et essais Se reporter au chapitre 417-01, du Manuel des schémas électriques pour les schémas et les informations sur les connecteurs. Outils spéciaux / Equipement d'atelier et outillage standard Kit de testeurs de bornes 29-011A Multimètre digital. Outil de diagnostic. Contrôle et vérification Note : Le module électronique générique (GEM) fait partie du boîtier électrique central (CJB). Note : Si le module GEM est remplacé, le module neuf doit être configuré après la pose. A cet effet, les données spécifiques au véhicule sont extraites du module à remplacer à l'aide de l'équipement de diagnostic et sont transférées dans le module neuf. Note : Avant d'extraire les données spécifiques au véhicule, s'assurer que toutes les connexions électriques du véhicule sont de nouveaux raccordées, de sorte que le module et l'outil de diagnostic puissent communiquer correct...
Lire la suite