The robotised gearbox with double clutch

-

Although we found an auto mode and a sequential mode, as a single-clutch AMT, the ISR dual clutch design is very different. It is in fact an assembly of two half-gearboxes. Each has its own clutch.
Thus, when a gear is engaged, the following report is pre-committed to him, which authorizes a change extremely fast speed (less than 10 milliseconds).
Furthermore, the torque transmission is continuous, thereby avoiding any jerk.
In short, dual-clutch AMT combines the advantages of the BVA and ISR single clutch, without their drawbacks.
This type of transmission meeting today a success.

advantages:

driving comfort
auto or sequential mode
consumption gain
passages ultrafast report
cons:

more expensive to buy than a BVA and a BVR
if the passage between the two reports is fast, it is much less so when we want to downshift 2 gears at once and vice versa (uphill).
Some examples: Peugeot DSC, EDC at Renault, Mercedes 7G-DCT, DSG / S-Tronic with Volkswagen and Audi ...

Commentaires

Enregistrer un commentaire

Posts les plus consultés de ce blog

Automatic Transmission - 6-Speed PowerShift Transmission - MPS6/6DCT450 - Diagnostic Strategy

-
Image
Diagnosis and Testing Refer to Wiring Diagrams Section 307-01, for schematic and connector information. General Equipment  diagnostic equipment Inspection and Verification Verify the customer concern. Visually inspect for obvious signs of mechanical or electrical damage. Visual Inspection Mechanical Electrical Fluid level too high/low Poor condition of fluid Fluid leak Damaged shift mechanism/linkages Damaged automatic transmission/ transaxle casing Fuse(s) Relay(s) Wiring harness Electrical connector(s) Selector lever module Transmission control module (TCM) If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step If the cause is not visually evident, verify the symptom and refer to the Ford diagnostic equipment to diagnose the system. Diagnostic Trouble Code (DTC) Chart NOTE: The following table should be used for guidance
Lire la suite

Electronic Engine Controls - 1.6L EcoBoost (118kW/160PS)

-
Image
Description and Operation Front view of engine Item Description 1 Variable camshaft timing oil control solenoid, exhaust camshaft 2 Ignition coil-on-plugs 3 CMP  (camshaft position)  Sensor - intake camshaft 4 Bypass solenoid valve 5 KS  (knock sensor)  sensor – cylinders 3 and 4 6 Electric throttle plate position sensors 7 Oil pressure switch 8 Shut-off solenoid valve 9 Electrically heated thermostat 10 KS  sensor – cylinders 1 and 2 11 The  MAP  (manifold absolute pressure)  sensor 12 Variable camshaft timing oil control solenoid, intake camshaft 13 Fuel pressure sensor – high-pressure circuit Rear view of engine Item Description 1 CMP  Sensor - exhaust camshaft 2 Fuel Metering Valve Comments: Part of the high-pressure fuel pump 3 Two-point  HO2S  (heated oxygen sensor) 4 Broadband  HO2S 5 The  ECT  (engine coola
Lire la suite

Diagnostic et essais Allumage automatique des phares

-
Image
Eclairage extérieur - Allumage automatique des phares Diagnostic et essais Se reporter au chapitre 417-01, du Manuel des schémas électriques pour les schémas et les informations sur les connecteurs. Outils spéciaux / Equipement d'atelier et outillage standard Kit de testeurs de bornes 29-011A Multimètre digital. Outil de diagnostic. Contrôle et vérification Note : Le module électronique générique (GEM) fait partie du boîtier électrique central (CJB). Note : Si le module GEM est remplacé, le module neuf doit être configuré après la pose. A cet effet, les données spécifiques au véhicule sont extraites du module à remplacer à l'aide de l'équipement de diagnostic et sont transférées dans le module neuf. Note : Avant d'extraire les données spécifiques au véhicule, s'assurer que toutes les connexions électriques du véhicule sont de nouveaux raccordées, de sorte que le module et l'outil de diagnostic puissent communiquer correct
Lire la suite