ABS SYSTEM

-
Description and Operation
General
At launch, the Focus C-MAX will only be available with disc brakes, Anti-lock Brake System (ABS) and Emergency Brake Assist (EBA).
The installation locations of the brake booster and the brake master cylinder on the bulkhead is different for LHD and RHD versions.
Front brakes
    Depending on the specification, different sizes of vented brake discs are installed.
  • 278 mm diameter
  • 300 mm diameter (not for use with R15 wheels)
Both versions are 25 mm thick. Conventional cast iron brake calipers are used; the brake caliper mountings are different for brake discs with diameters of 278 mm and 300 mm.
Rear brakes
The brake discs on the rear wheels have a diameter of 265 mm or 280 mm and are 11 mm thick.
When resetting a brake piston in the brake caliper, the piston needs to be turned using the standard brake piston resetting tool. The correct procedure is described in the relevant section of the workshop literature.
Brake calipers pre-filled with brake fluid are available in service. These calipers simplify the process of bleeding the brake system after installing a new brake caliper.
All vehicles are equipped with EBA which is part of the brake booster.
Vehicles with ABS only are equipped with the Teves MK70 system.
Vehicles with both ABS and traction control system (TCS) are equipped with the Teves MK60 system.

The electronic stability program is available as an option with ABS and TCS

Commentaires

Enregistrer un commentaire

Posts les plus consultés de ce blog

Automatic Transmission - 6-Speed PowerShift Transmission - MPS6/6DCT450 - Diagnostic Strategy

-
Image
Diagnosis and Testing Refer to Wiring Diagrams Section 307-01, for schematic and connector information. General Equipment  diagnostic equipment Inspection and Verification Verify the customer concern. Visually inspect for obvious signs of mechanical or electrical damage. Visual Inspection Mechanical Electrical Fluid level too high/low Poor condition of fluid Fluid leak Damaged shift mechanism/linkages Damaged automatic transmission/ transaxle casing Fuse(s) Relay(s) Wiring harness Electrical connector(s) Selector lever module Transmission control module (TCM) If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step If the cause is not visually evident, verify the symptom and refer to the Ford diagnostic equipment to diagnose the system. Diagnostic Trouble Code (DTC) Chart NOTE: The following table should be used for guidance
Lire la suite

Electronic Engine Controls - 1.6L EcoBoost (118kW/160PS)

-
Image
Description and Operation Front view of engine Item Description 1 Variable camshaft timing oil control solenoid, exhaust camshaft 2 Ignition coil-on-plugs 3 CMP  (camshaft position)  Sensor - intake camshaft 4 Bypass solenoid valve 5 KS  (knock sensor)  sensor – cylinders 3 and 4 6 Electric throttle plate position sensors 7 Oil pressure switch 8 Shut-off solenoid valve 9 Electrically heated thermostat 10 KS  sensor – cylinders 1 and 2 11 The  MAP  (manifold absolute pressure)  sensor 12 Variable camshaft timing oil control solenoid, intake camshaft 13 Fuel pressure sensor – high-pressure circuit Rear view of engine Item Description 1 CMP  Sensor - exhaust camshaft 2 Fuel Metering Valve Comments: Part of the high-pressure fuel pump 3 Two-point  HO2S  (heated oxygen sensor) 4 Broadband  HO2S 5 The  ECT  (engine coola
Lire la suite

Diagnostic et essais Allumage automatique des phares

-
Image
Eclairage extérieur - Allumage automatique des phares Diagnostic et essais Se reporter au chapitre 417-01, du Manuel des schémas électriques pour les schémas et les informations sur les connecteurs. Outils spéciaux / Equipement d'atelier et outillage standard Kit de testeurs de bornes 29-011A Multimètre digital. Outil de diagnostic. Contrôle et vérification Note : Le module électronique générique (GEM) fait partie du boîtier électrique central (CJB). Note : Si le module GEM est remplacé, le module neuf doit être configuré après la pose. A cet effet, les données spécifiques au véhicule sont extraites du module à remplacer à l'aide de l'équipement de diagnostic et sont transférées dans le module neuf. Note : Avant d'extraire les données spécifiques au véhicule, s'assurer que toutes les connexions électriques du véhicule sont de nouveaux raccordées, de sorte que le module et l'outil de diagnostic puissent communiquer correct
Lire la suite