Injectors engine operation-10-

-

Injectors




The electromagnetically controlled injectors dose and atomize the fuel. The quantity of injected fuel is regulated by the duration of actuation of the fuel injectors. The fuel injectors are either closed (not actuated) or opened (actuated). Each cylinder has its own injector. The injection is accurately dosed and takes place at a time determined by the PCM. Injection takes place immediately in front of the intake valves of the cylinder.


1---Electrical connection
2---Seal
3---Fuel inlet with fine sieve
4---Housing
5---Coil
6---Spring
7---Valve needle with solenoid armature
8---Valve seat with nozzle hole disk
The fuel injectors consist of a housing with fuel passages, a coil and an injector needle with a solenoid armature. The fuel inlet in the injector features a fine sieve. The injectors are controlled via end-stages integrated into the PCM with the signal calculated by the engine management system on the earth side. Power is supplied via the Powertrain Control Module relay and fuse F9 in the BJB. The injected fuel quantity depends on the opening time, the fuel pressure and the diameter of the nozzle holes. There are two holes in the nozzle hole disk. These are arranged so that two jets of fuel emerge. Each jet supplies one intake valve.

Commentaires

Enregistrer un commentaire

Posts les plus consultés de ce blog

Automatic Transmission - 6-Speed PowerShift Transmission - MPS6/6DCT450 - Diagnostic Strategy

-
Image
Diagnosis and Testing Refer to Wiring Diagrams Section 307-01, for schematic and connector information. General Equipment  diagnostic equipment Inspection and Verification Verify the customer concern. Visually inspect for obvious signs of mechanical or electrical damage. Visual Inspection Mechanical Electrical Fluid level too high/low Poor condition of fluid Fluid leak Damaged shift mechanism/linkages Damaged automatic transmission/ transaxle casing Fuse(s) Relay(s) Wiring harness Electrical connector(s) Selector lever module Transmission control module (TCM) If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step If the cause is not visually evident, verify the symptom and refer to the Ford diagnostic equipment to diagnose the system. Diagnostic Trouble Code (DTC) Chart NOTE: The following table should be used for guidance
Lire la suite

Electronic Engine Controls - 1.6L EcoBoost (118kW/160PS)

-
Image
Description and Operation Front view of engine Item Description 1 Variable camshaft timing oil control solenoid, exhaust camshaft 2 Ignition coil-on-plugs 3 CMP  (camshaft position)  Sensor - intake camshaft 4 Bypass solenoid valve 5 KS  (knock sensor)  sensor – cylinders 3 and 4 6 Electric throttle plate position sensors 7 Oil pressure switch 8 Shut-off solenoid valve 9 Electrically heated thermostat 10 KS  sensor – cylinders 1 and 2 11 The  MAP  (manifold absolute pressure)  sensor 12 Variable camshaft timing oil control solenoid, intake camshaft 13 Fuel pressure sensor – high-pressure circuit Rear view of engine Item Description 1 CMP  Sensor - exhaust camshaft 2 Fuel Metering Valve Comments: Part of the high-pressure fuel pump 3 Two-point  HO2S  (heated oxygen sensor) 4 Broadband  HO2S 5 The  ECT  (engine coola
Lire la suite

Diagnostic et essais Allumage automatique des phares

-
Image
Eclairage extérieur - Allumage automatique des phares Diagnostic et essais Se reporter au chapitre 417-01, du Manuel des schémas électriques pour les schémas et les informations sur les connecteurs. Outils spéciaux / Equipement d'atelier et outillage standard Kit de testeurs de bornes 29-011A Multimètre digital. Outil de diagnostic. Contrôle et vérification Note : Le module électronique générique (GEM) fait partie du boîtier électrique central (CJB). Note : Si le module GEM est remplacé, le module neuf doit être configuré après la pose. A cet effet, les données spécifiques au véhicule sont extraites du module à remplacer à l'aide de l'équipement de diagnostic et sont transférées dans le module neuf. Note : Avant d'extraire les données spécifiques au véhicule, s'assurer que toutes les connexions électriques du véhicule sont de nouveaux raccordées, de sorte que le module et l'outil de diagnostic puissent communiquer correct
Lire la suite